半球谐振子疲劳寿命分析与仿真

半球谐振子的寿命和损伤是直接影响高精度半球谐振陀螺使用时长和安全性的重要因素。目前国内加工的半球谐振子所用的熔融石英玻璃材料主要依靠进口，采用传统的疲劳寿命实验确定方法成本过于昂贵，因此需要利用疲劳分析软件对半球谐振子的疲劳寿命进行分析。文章通过半球谐振陀螺应力分析，采用ANSYS软件对熔融石英半球谐振子进行应力分析仿真，确定因残余应力所引起的疲劳危险部位，并在疲劳部位进行裂纹扩展分析，得到 、 和 型应力强度因子，以使在半球谐振子结构设计和使用过程中对易疲劳的部位进行有效监控和预防。     

石英玻璃的等离子体抛光技术研究现状

具有耐腐蚀、热膨胀系数低等诸多优良物理化学特性的石英玻璃在高性能光学系统中被广泛使用。要求元件达到纳米级别的表面粗糙度，而且没有损伤层和残余应力，因此精加工之后的超精密抛光工序尤为重要。本文介绍了气囊、磁流变、弹性发射、离子束等几种石英玻璃的精密抛光方法，侧重阐述了国内外等离子体的抛光技术，包括等离子体辅助化学刻蚀、等离子体喷射加工、等离子化学蒸发加工研究进展及取得的成果；且对等离子体的未来发展进行概述。     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

比例与非比例加载下30CrMnSiA钢多轴高周疲劳失效分析

为了分析比例与非比例加载下,30CrMnSiA钢的多轴高周疲劳的失效规律。通过对30CrMnSiA钢材料开展比例与非比例(δ=90°)加载下的多轴高周疲劳试验,研究了应力幅比和相位差对疲劳寿命、断口特征及裂纹起裂角度的影响。试验结果表明,对于比例与非比例加载,随着应力幅比的增大,多轴疲劳寿命逐渐增加。对疲劳断口分析发现,裂纹萌生于试件表面,断口有明显的疲劳源区、扩展区和瞬断区,不同加载路径下的试件断口形式有明显差异。通过对起裂角度的分析发现,应力幅比大于0.25时表面裂纹有明显的第Ⅰ阶段向第Ⅱ阶段的转变,且第Ⅰ阶段沿着接近最大剪应力幅值平面方向扩展,第Ⅱ阶段沿着接近最大正应力平面方向扩展。此外,对典型试件的疲劳断口及表面扩展路径进行了分析,研究表明多轴疲劳试验试件裂纹的特征比值在0.3~0.5之间,且裂纹沿深度方向扩展至300 μm时占总寿命的85%以上。      

平板表面薄圆柱绕流摩擦力矢量场全局测量

针对壁面摩擦力矢量场测量问题,基于剪切敏感液晶(SSLC)涂层技术建立了一种测量平板表面摩擦力矢量场的方法。该方法基于多视角测量原理,采用六台同步相机从不同方向同时采集SSLC涂层在摩擦力作用下的颜色变化,与采用单台相机相比能够降低测量噪声,并且具有测量非定常流动的摩擦力场的潜力。应用该方法测量了平板表面薄圆柱绕流的摩擦力矢量场,结果表明:(1)SSLC涂层能够以彩色方式定性显示壁面摩擦力信息;(2)通过对不同方向观测的SSLC涂层颜色进行分析处理,该方法能够高分辨率测量薄圆柱绕流的摩擦力矢量场,详细地捕获了流动特征;(3)同一份SSLC涂层可以重复使用并且可用于测量不同的摩擦力矢量场。     

超高强高韧马氏体时效钢热变形及航天应用研究

对于航天用超高强高韧C300马氏体时效钢来说,热加工过程中获得等轴细小的再结晶晶粒是实现该钢强韧性最佳匹配的关键环节。采用Gleeble-3800热模拟试验机在温度为850～1 150℃、应变速率为0.01～10 s~(-1)的条件下,对超高强高韧C300马氏体时效钢进行高温轴向压缩变形试验,获得了高温流变曲线,并观察变形后的金相组织。结果表明:C300马氏体时效钢的流变应力和峰值应变随着变形温度的升高和应变速率的降低而减小;试验钢在真应变为0.92、应变速率为0.01～10 s~(-1)的条件下,随着变形速率的提高,其发生完全动态再结晶的温度也逐渐升高,最佳热变形温度区间为1 050～1 150℃;测得试验钢的热变形激活能Q值为391.2 kJ/mol,建立了其热变形本构方程。结果能为C300马氏体钢的数值模拟和热加工工艺的制定提供理论基础。     

基于随机维纳过程的航空发动机性能衰退研究

针对发动机下发间隔预测的问题，研究了发动机性能衰退规律。基于发动机排气温度裕度（EGTM）数据，建立了随机维纳模型，并使用严酷度因子修正模型，表征不同的工作条件对发动机的影响。利用期望最大化（EM）算法结合贝叶斯定理，对模型参数求解，最终得到了基于性能衰退的发动机平均下发间隔。研究结果表明，在严酷度因子为1.2696的使用条件下，某型号航空发动机性能衰退平均下发间隔为8219循环；基于该模型预测的发动机平均下发间隔与厂商建议的下发时间之间的误差仅为1.7%。     

Two-stream instability generation in the lunar ionosphere

The Two-stream Instability (TSI) generation is studied analytically in the lunar ionosphere. The TSI is a tiny perturbation in the electron plasma density, due to which an electric field grows with time and this growth is facilitated by the electron plasma in the background. In lunar ionosphere, the TSI comes into existence when the solar wind interacts unhindered with the tenuous lunar electron plasma in the surface bound exosphere. In this study, the conditions which allow the TSI to form and the subsequent instability growth with time i.e. the growth factor, is estimated. Initially, the threshold condition for the TSI to take place is determined. Thereafter, the solar wind and lunar plasma parameter contribution to trigger TSI is investigated along with the effect of these parameters in the evolution of TSI. The plasma TSI evolution with the passage of time is also depicted in phase space diagram with Particle-In-Cell simulations.     

Fault mode probability factor based fault-tolerant control for dissimilar redundant actuation system

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model precision and computation time, a Moving Window (MW) method is used to determine the applied historical statistics. The FMPF based FTC strategy is developed for the amended system model where the system estimation and Linear Quadratic Regulator (LQR) are updated at the end of system sampling period. The simulations of DRAS system subjected to multiple faults have been performed and the results indicate the effectiveness of the proposed approach.     

光敏推进剂激光烧蚀过程建模与仿真

相较于传统大卫星,微小卫星具有结构紧凑、质量轻便和成本低廉的特点。然而,受功率和质量负载的限制,微小卫星一般不装备推进系统,其航线也局限于近地轨道。为扩展微小卫星的功能,满足日益复杂的任务需求,需给其配备合适的微推进系统。固体推进系统具有结构简单、寿命长、可靠性高的优点,但无法重复启动。为得到可重复启动的固体微推进系统,设计了一种非自持燃烧的光敏推进剂,采用激光控制其燃烧。在背压为大气压的环境下,利用高速摄像机拍摄燃烧过程并记录燃速。之后,对光敏推进剂的激光烧蚀过程进行建模。分析结果表明:激光可控制光敏推进剂的燃烧,燃速与激光强度成线性关系;该光敏推进剂的最小激光点火强度为0.28 W/mm~2;燃速计算值与实测值的误差在10%以内,证明该数学模型具备工程应用价值。